View RN42HID-IRM_8459587.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2015 microchip technology inc. ds50002328a-page 1 rn42/rn42n features fully qualified bluetooth ? version 2.1 module, sup- ports version 2.1 + enhanced data rate (edr) ascii command interface over uart postage-stamp-sized form factor: - rn42: 13.4 x 25.8 x 2.4 mm - rn42n: 13.4 x 20.5 x 2.4 mm low-power (26 ? a sleep, 3 ma connected, 30 ma transmit) uart (spp or hci) and usb (hci only) data con- nection interfaces sustained spp data rates: 240 kbps (slave mode), 300 kbps (master mode) hci data rates: 1.5 mbps sustained, 3.0 mbps burst in hci mode embedded bluetooth stack profiles include: gap, sdp, rfcomm, l2cap protocols, with spp, hid, and dun profile support (does not require any host stack). bluetooth sig qualified, end product listing castellated smt pads for easy and reliable pcb mounting class 2 power amplifier with on-board pcb trace antenna (rn42) or external antenna (rn42n) compliance (rn42) - modular certified for the united states (fcc) and canada (ic) - european r&tte directive assessed radio module - australia/new zealand/japan/korea/taiwan - bluetooth sig qdid integrated crystal, internal voltage regulator, matching circuitry, power amplifier, low noise, memory amplifier and pcb antenna easy integration into final product - minimize prod- uct development, quicker time to market compatible with microchip microcontroller families (pic16f, pic18f, pic24f/h, dspic33 and pic32) up to 10 meter range applications cable replacement barcode scanners measurement and monitoring systems industrial sensors and controls medical devices note 1: for customer part numbers, see section 4.0 ordering information . information on firmware versions can be found on the rn42/rn42n product web page and the bluetooth data module command reference and advanced information users guide . rn42/rn42n module variants (1) model antenna firmware description rn42 integral 4.77, 6.15 class 2, 2.1+edr, spp profile rn42hci integral n/a class 2, 2.0+edr, hci over uart rn42hid integral 6.11 class 2, 2. 1+edr, hid and spp profiles rn42u integral n/a class 2, 2.0+edr, hci over usb rn42apl integral 5.36, 5.43, 5.45 class 2, 2.1+edr, spp & mfi profiles rn42n external 4.77, 6.15 class 2, 2.1+edr, spp profile rn42nhci external n/a class 2, 2.0+edr, hci over uart rn42nhid external 6.11 class 2, 2.1+edr, hid and spp profiles rn42nu external n/a class 2, 2.0+edr, hci over usb rn42napl external 5.36, 5.43, 5.45 class 2, 2.1+edr, spp & mfi profiles class 2 bluetooth ? module with edr support downloaded from: http:///
rn42/rn42n ds50002328a-page 2 ? 2015 microchip technology inc. to our valued customers it is our intention to provide our valued customers with the bes t documentation possible to ensure successful use of your micro chip products. to this end, we will continue to improve our publi cations to better suit your needs. our publications will be refined and enhanced as new volumes and updates are introduced. if you have any questions or comments regar ding this publication, please contact the marketing communications department via e-mail at docerrors@microchip.com . we welcome your feedback. most current data sheet to obtain the most up-to-date version of this data s heet, please register at our worldwide web site at: http://www.microchip.com you can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page . the last character of the literature number is the vers ion number, (e.g., ds30000000a is version a of document ds30000000). errata an errata sheet, describing minor opera tional differences from the data sheet a nd recommended workarounds, may exist for curren t devices. as device/documentation is sues become known to us, we will publish an er rata sheet. the errata will specify the revisi on of silicon and revision of document to which it applies. to determine if an errata sheet exists for a partic ular device, please check with one of the following: microchips worldwide web site; http://www.microchip.com your local microchip sales office (see last page) when contacting a sales office, please spec ify which device, revision of silicon and dat a sheet (include literature number) you are using. customer notification system register on our web site at www.microchip.com to receive the most current information on all of our products. table of contents 1.0 device overview ...........................................................................................................................................................................3 2.0 application information..................................................................................................................................................................7 3.0 regulatory approval......................................................................................................... ...........................................................12 4.0 ordering information ...................................................................................................................................................................18 appendix a: revision history................................................................................................... .............................................................19 the microchip web site........................................................................................................................................................................21 customer change notification service .................................................................................................................................................21 customer support............................................................................................................... ..................................................................21 product identification system ...............................................................................................................................................................23 downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 3 rn42/rn42n 1.0 device overview the rn42/rn42n module is a small form factor, low- power, class 2 bluetooth radio that is ideal for designers who want to add wireless capability to their products without spending si gnificant time and money developing bluetooth-specific hardware and software. the rn42/rn42n supports multiple interface protocols, is simple to design in, and is fully certified, making it a complete embedded bluetooth solution. with its high-performance, pcb trace antenna (rn42) or external antenna (rn42n), and support for bluetooth edr, the rn42/rn42n delivers up to a 3- mbps data rate for distances up to 10 meters. 1.1 mcu interface the rn42/rn42n module is managed through ascii commands via the uart and/or pio signals. a micro- controller unit (mcu) or host processor sends com- mands to configure module features, read status, and manage bluetooth data connections. as shown in figure 1-1 , the uart tx and rx are required to communicate with module, and transfer data across bluetoo th spp connection. connecting the hardware flow control lines cts and rts is highly recommended for applications that transmits a continuous stream of data. the module can be configured locally via the uart or over-the-air. to support instant cable replacement, auto-discovery/pairing does not require software con- figuration. additionally, the module supports auto-con- nect master, i/o pin (dtr), and character-based trigger modes. figure 1-1: rn42/rn42n to mcu interface table 1-1 , table 1-2 , ta b l e 1 - 3 , ta b l e 1 - 4 , and ta b l e 1 - 5 provide the modules environmental conditions, elec- trical characteristics, dime nsions, radio characteristics, and digital i/o characteristics. 1.2 ascii command and data interface the bluetooth data module advanced users guide provides a complete description of the ascii command and data interface for the rn42/rn42n module. table 1-1: environmental conditions parameter value temperature range (operating) -40 o c ~ 85 o c temperature range (storage) -40 o c ~ 85 o c relative humidity (operating) ?? 90% relative humidity (storage) ?? 90% moisture sensitivity level 1 table 1-2: electrical characteristics parameter min. typ. max. units supply voltage (dc) 3.0 3.3 3.6 v average power consumption radio on (discovery or inquiry window time) (1) 4 0m a connected idle (no sniff) 25 ma connected idle (sniff 100 ms) 12 ma connected with data transfer 40 45 50 ma deep sleep idle mode 26 ? a note 1: this characteristic applies if, in slave mode, there are bursts of radio on time that vary with the windows. the window setting determines the average current. downloaded from: http:///
rn42/rn42n ds50002328a-page 4 ? 2015 microchip technology inc. table 1-3: module dimensions parameter rn42 rn42n units size 13.4 x 25.8 x 2.4 13.4 x 20.5 x 2.4 mm weight 0.045 0.040 oz. table 1-4: radio characteristics parameter frequency (ghz) min. typ. max. bluetooth specification units sensitivity at 0.1% ber 2.402 -80 -86 -70 dbm 2.441 -80 -86 dbm 2.480 -80 -86 dbm rf transmit power (1) rn42 2.402 4 dbm 2.441 4 dbm 2.480 4 dbm rf transmit power (1) rn42n 2.402 4 dbm 2.441 4 dbm 2.480 4 dbm initial carrier frequency tolerance 2.402 5 75 75 khz 2.441 5 75 khz 2.480 5 75 khz 20-db bandwidth for modulated carrier 900 1000 1000 khz drift (five slots packet) 15 40 khz drift rate 13 20 khz ? f1 avg maximum modulation 2.402 140 165 175 > 140 khz 2.441 140 165 175 khz 2.480 140 165 175 khz ? f2 avg minimum modulation 2.402 140 190 115 khz 2.441 140 190 khz 2.480 140 190 khz note 1: normal mode table 1-5: digital i/o characteristics 3.0 v vdd 3.3 v min. typ. max. units input logic level low -0.4 +0.8 v input logic level high 0.7 vdd vdd + 0.4 v output logic level low 0.2 v output logic level high vdd - 0.2 v all i/o pins (except reset) defaul t to weak pull down +0.2 +1.0 +5.0 ? a downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 5 rn42/rn42n figure 1-2 and figure 1-3 show the modules dimensions. figure 1-2: rn42 module dimensions figure 1-3: rn42n module dimensions figure 1-4 and figure 1-5 show the pinout and table 1-6 describes the modules pins. figure 1-4: rn 42 pin diagram figure 1-5: rn42n pin diagram 0.80mm 0.02.6 1.13.6 4.9 6.1 7.3 8.5 9.8 10.812.3 13.4 0.0 0.7 2.8 4.0 5.2 6.4 7.6 8.8 10.0 11.2 12.4 13.6 14.8 16.0 25.819.7 20.5 pcb outline: +/- 0.13 mm pcb thickness: +/- 0.1 mm tolerances: top view side view dimensions are in millimeters 0.0 0.8 2.4 0.0 25.8 0.80mm 0.02.6 1.13.6 4.9 6.1 7.3 8.5 9.8 10.812.3 13.4 0.0 0.7 2.8 4.0 5.2 6.4 7.6 8.8 10.0 11.2 12.4 13.6 14.8 16.0 19.7 20.5 pcb outline: +/- 0.13 mm pcb thickness: +/- 0.1 mm tolerances: top view dimensions are in millimeters 0.0 0.8 2.4 0.0 20.5 side view 8.910.5 7.3 gnd spimosi gpio6gpio7 reset spiclock pcmclk pcmsync pcmin pcmout vdd gnd spimisospicsb gpio4 gpio5 gpio3 gpio2 usbd- usbd+ uartcts uartrts uarttx uartrx 12 3 4 5 6 7 8 9 10 11 12 2423 22 21 20 19 18 17 16 15 14 13 aio1 gnd gpio11 gpio10 gpio9gpio8 gnd aio0 35 29 34 33 32 31 28 30 rn42 top vie gnd spimosi gpio6gpio7 reset spiclock pcmclk pcmsync pcmin pcmout vdd gnd spimisospicsb gpio4 gpio5 gpio3 gpio2 usbd- usbd+ uartcts uartrts uarttx uartrx 12 3 4 5 6 7 8 9 10 11 12 2423 22 21 20 19 18 17 16 15 14 13 aio1 gnd gpio11 gpio10 gpio9gpio8 gnd aio0 35 29 34 33 32 31 28 30 rn42n top vie gnd rfpad gnd 27 26 25 downloaded from: http:///
rn42/rn42n ds50002328a-page 6 ? 2015 microchip technology inc. table 1-6: pin description pin type abbreviation: a = analog, d = digital, i = input, o = output. note 1: pin numbers 7 through 10 are reserved for future use. pin symbol type description 1 gnd power ground reference 2 spi_mosi di ( optional ) factory diagnostic, programming and test. see section 2.8 spi interface . 3 gpio6 di set bluetooth master. if gpio6 = high, module connects to the stored address. if gpio3 = high, module enters new discovery/pairing mode. 4 gpio7 dio set baud rate (high = force 9,600, low = 115k or firmware setting) 5 reset di active-low reset 6 spi_clk di ( optional ) factory diagnostic and test. see section 2.8 spi interface . 7 pcm_clk dio (do not connect) pcm interface (1) 8 pcm_sync dio (do not connect) pcm interface (1) 9 pcm_in di (do not connect) pcm interface (1) 10 pcm_out do (do not connect) pcm interface (1) 11 vdd power positive supply 12 gnd power ground reference 13 uart_rx di uart receive input 14 uart_tx do uart transmit output 15 uart_rts do uart rts, goes high to disable host transmitter 16 uart_cts di uart cts, if set high, it disables transmitter 17 usb_d+ dio usb port. 1.5k pullup activated when usb port is ready (~500 ms after reset). 18 usb_d- dio usb port 19 gpio2 dio status, high when connected, low otherwise. see section 2.3 connection status . 20 gpio3 di auto-discovery mode = high. if gpio6 = high, module performs device enquiry scan searching for a device with matching class of 0x55aa. if a device is found, the address of the device is stored in the remote address field and auto-connects. if gpio6 = low, module enters slave mode with special matching class of 0x55aa and waits for a master to discover it. 21 gpio5 dio status, toggles based on state, low on connect. see section 2.3 connection status . 22 gpio4 dio set factory defaults. see section 2.2 factory reset using gpio4 . 23 spi_csb di ( optional ) factory diagnostic and test. see section 2.8 spi interface . 24 spi_miso do ( optional ) factory diagnostic and test. see section 2.8 spi interface . 25 gnd power ground reference (rn42n only) 26 rf ant aio antenna, 50-ohm impedance (rn42n only) 27 gnd power ground reference (rn42n only) 28 gnd power ground reference 29 gnd power ground reference 30 aio0 aio ( not used ) optional analog input 31 gpio8 do uart tx/rx data activity 32 gpio9 dio i/o 33 gpio10 dio i/o (remote dtr signal) 34 gpio11 dio i/o (remote rts signal) 35 aio1 aio ( not used ) optional analog input downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 7 rn42/rn42n 2.0 application information the following sections provide information on design- ing with the rn42/rn42n module, including radio interference, factory reset, solder reflow profile, con- nection status, and so on. 2.1 reset circuit the rn42/rn42n contains a weak internal pull-up to vcc, and the reset polarity is active low. the modules reset pin has an optional power-on reset circuit with a delay, which should only be required if the input power supply has a very slow ramp or tends to bounce or have instability on power-up. often a microcontroller or embedded cpu i/o is available to generate the reset once power is stable. if not, designers can use one of the many low-cost power supervisor chips available, such as the mcp809 or mcp102/121. 2.2 factory reset using gpio4 it is recommended to connect the gpio4 pin to a switch, jumper, or resistor so it can be accessed. this pin can be used to reset the module to its factory default settings, which is crit ical in situations where the module has been misconfigure d. to reset the module to the factory defaults, gpio4 should be high on power-up and then toggle between low and high twice with a 1 second wait between the low-high transitions. 2.3 connection status gpio5 is available to drive an led, and it blinks at var- ious speeds to indicate status, see table 2-1 . gpio2 is an output that directly reflects the connection state as shown in ta b l e 2 - 2 . 2.4 module mounting details figure 2-1 and figure 2-2 show the recommended pcb footprint for the rn42 and rn42n, respectively. when laying out the carrier board for the rn42 module, the areas under the antenna and shielding connections should not have surface traces, ground planes, or exposed vias. figure 2-3 and figure 2-4 show the recommended mounting details for the rn42 and rn42n, respec- tively. for optimal radio performance, the rn42 mod- ules antenna end should protrude at least 31 mm beyond any metal enclosure. figure 2-5 shows examples of good, bad, and accept- able positioning of the rn42/rn42n on the host pcb. figure 2-1: rn42 recommended pcb footprint table 2-1: gpio5 status gpio5 status description toggle at 1 hz the module is discoverable and waiting for a connection. toggle at 10 hz the module is in command mode. high the module is connected to another device over bluetooth. table 2-2: gpio2 status gpio2 status description high the module is connected to another device over bluetooth. low the module is not connected over bluetooth. 0.70mm 0.80mm 2.00mm 0.02.6 1.13.6 4.9 6.1 7.3 8.5 9.8 10.812.3 13.4 0.0 0.7 2.8 4.0 5.2 6.4 7.6 8.8 10.0 11.2 12.4 13.6 14.8 16.0 25.819.7 shield pads 4 corners 1.0 x 1.8mm 20.5 do not locate vias or surface traces under shield pads top view dimensions are in millimeters downloaded from: http:///
rn42/rn42n ds50002328a-page 8 ? 2015 microchip technology inc. figure 2-2: rn42n recommended pcb footprint figure 2-3: rn42 module mounting details figure 2-4: rn42n module mounting details 0.70mm 0.80mm 2.00mm 0.02.6 1.13.6 4.9 6.1 7.3 8.5 9.8 10.812.3 13.4 0.0 0.7 2.8 4.0 5.2 6.4 7.6 8.8 10.0 11.2 12.4 13.6 14.8 16.0 19.7 shield pads 4 corners 1.0 x 1.8mm 20.0 do not locate vias or surface traces under shield pads top view dimensions are in millimeters 8.910.5 7.3 20.5mm 5.3mm top view keep area around antenna (approximatel 31 mm) clear of metallic structures for best performance 31mm edge of ground plane 31cm note: example u.fl connector layout top view downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 9 rn42/rn42n figure 2-5: rn42 host pcb example layout 2.5 external antenna types (rn42n) the rn42n modules antenna pin (pin 26) provides a 50-ohm impedance to external antennas. pin 25 can connect directly to a coax ial cable or to an antenna connector such as a u.fl or reverse polarity sma. the pcb trace from pin 26 to the coaxial cable or con- nector should be less than 0.2 inches (5 mm) for mini- mum loss and the best impedance match. if the pcb trace is longer, it should be a 50-ohm impedance microstrip trace. connect adjacent ground pins 25 and 27 to a low-impedance ground on the host pcb and the antenna connection. figure 2-4 gives example host pcb layout to a u.fl connector. 2.6 hci mode microchip offers the host controller interface (hci) mode in addition to the standard operational mode of its bluetooth modules (standard mode refers to the on- board stack running on the module). in hci mode, the on-board stack is bypassed and the module is put in a state that runs the bluetooth base- band. the hci provides a command reference inter- face to the baseband controller and the link manager, and provides access to the hardware status and control registers. this interface provides a uniform method for accessing the bluetooth baseband capabilities. in this mode, the bluetooth stack is no longer on-board the module. it is offloaded to the interfacing host pro- cessor. the bluetooth module is used as a radio, per- forming the lower level mac functionalities, while the application stack runs on the host processor. using the module in hci mode enables designers to implement profiles that are not natively supported on the bluetooth module. microchip offers hci mode in two hardware interfaces: hci over uart (rn42hci-i/rm) hci over usb (rn42u-i/rm) 2.6.1 hci over uart in this mode, the hardware interface between the host processor and the bluetooth module is the uart con- figured at 115.2kbps. the uart hardware flow control signals are required between the host processor and the bluetooth module for the hci interface to work. failure to do so can cause the host processor and the bluetooth module to become out of sync and break the bluetooth link. 2.6.2 hci over usb in this mode, the hardware interface between the host processor and the bluetooth module is the usb. in this architecture, the bluetooth module is the usb slave and the host processor is the usb host. using the usb interface offers the advantage of a faster data link between the bluetooth module and the host processor. with this interface, it is possible to achieve bluetooths theoretical maximum throughput of 3 mpbs. no copperin these areas rn42 okay rn42 best rn42 okay rn42 okay note: hci mode is only available by ordering part rn42hci and rn42hci for uart interface; or rn42u and rn42u for usb interface. downloaded from: http:///
rn42/rn42n ds50002328a-page 10 ? 2015 microchip technology inc. 2.7 soldering recommendations the rn42/rn42n wireless module was assembled using standard lead-free reflow profile ipc/jedec j- std-020. the module can be soldered to the host pcb using standard leaded and lead-free solder reflow profiles. to avoid damaging the module, the following recom- mendations are given: microchip technology application note, an233 solder reflow recommendation (ds00233) pro- vides solder reflow recommendations do not exceed peak temperature (t p ) of 250 c refer to the solder paste data sheet for specific reflow profile recommendations use no-clean flux solder paste do not wash as moisture can be trapped under the shield use only one flow. if the pcb requires multiple flows, apply the module on the final flow. 2.8 spi interface the spi interface is primarily used for factory program- ming, test, and diagnostics. although not required, the spi interface is useful for restoring a corrupted flash image or enabling test modes required for certification testing. when module is installed in a final product that requires european type approval, see section 3.3 europe , it is recommended that the spi interface should be accessible via 6-pin header as shown in figure 2-6 . figure 2-6: optional spi interface 2.9 bluetooth sig qdid the rn42 has a qdid registered with the bluetooth sig. the manufacturer using the rn42 module in their end product can reference this qdid when filing an epl (end product listing) to use bluetooth ? brand and logo. for more information, please visit the bluetooth sig at www.bluetooth.org . qdid: b014867 downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 11 rn42/rn42n 2.10 application schematic figure 2-7 shows an example application circuit. this schemati c is for the rn-42-ek development tool. for details on how to connect rn42/rn42n to a microcontroller, see section 1.1 mcu interface . figure 2-7: example application circuit tx d rx d gnd 1 spi _mosi 2 pi o6 3 pi o7 4 reset 5 spi _sck 6 pcm_cl k 7 pcm_sync 8 pcm_i n 9 pcm_out 10 vdd 11 gnd 12 uart_rx 13 uart_tx 14 uart_rts 15 uart_cts 16 usb_d+ 17 usb_d- 18 pi o2 19 pi o3 20 pi o5 21 pi o4 22 spi _cs# 23 spi _mi so 24 gnd 2 8 gnd 29 a io0 3 0 pi o8 31 pi o9 3 2 pi o10 33 pio1 1 34 aio1 35 sh ield 0 m1 rn42 module spi _mi so spi _mosi spi _sck spi _ss rt s ct s reset _n pi o6 pi o7 pi o4 pi o5 pi o3 pi o2 aio1 ai o0 pio11 pio10 pi o9 pio8 1 2 3 4 5 6 j3 spi master spi _mi so spi _mosi spi _sck spi _ss 3.3v 3.3v pcm_cl k pcm_sync pcm_out pcm_i n 100k r17 300k r18 100k r16 300k r15 v b 1 v b2 a io0 a io1 1 2 3 4 5 6 7 8 9 10 11 12 j1 header 1 1 2 3 4 5 6 7 8 9 10 11 12 j2 header 2 pi o6 pi o7 reset _n rx d tx d rt s ct s pi o4 pi o3 pi o2 pi o11 pi o10 pi o9 pi o8 3.3v vb1 vb2shdn d_nd_p txd rxdrts cts vbus reset 18 3v 3out 16 usbdp 14 usbdm 15 gnd 1 7 cbus2 10 cbus1 21 vc ci o 1 cbus3 11 cbus4 9 cbus0 22 gnd 20 ri 3 dcd 7 dsr 6 dtr 31 cts 8 rts 32 rxd 2 txd 30 vcc 19 osci 27 osco 28 agnd 24 test 2 6 gnd 4 thpad 33 ft232rq u3 100nf c6100nf c5 100nf c4 gnd 5 d+ 3 d- 2 vbus 1 mtab 6 usb mini b j4 3k3 r12 3k3 r13 3k3 r11 3k3 r14 vbus 3.3v vbus vi n 1 g nd 2 shdn 3 byp 4 vout 5 u1 tc1185 1uf c2 1uf c1 shdn 3k3 r1 12 3 4 s1 3k3 r10 3k3 r9 3k3 r8 3k3 r7 3.3v pi o4 pi o3 pi o6 pi o7 red led d2 activity pi o5 3.3v pi o8 green led d1 connection status 470 r2470 r3 downloaded from: http:///
rn42/rn42n ds50002328a-page 12 ? 2015 microchip technology inc. 3.0 regulatory approval this section outlines the regulatory information for the rn42 module for the following countries: united states canada europe australia new zealand japan korea taiwan 3.1 united states the rn42 module has received federal communica- tions commission (fcc) cfr47 telecommunications, part 15 subpart c intentional radiators modular approval in accordance with part 15.212 modular transmitter approval. modular approval allows the end user to integrate the rn42 module into a finished prod- uct without obtaining subsequent and separate fcc approvals for intentional radiation, provided no changes or modifications are made to the module cir- cuitry. changes or modifications could void the users authority to operate the eq uipment. the end user must comply with all of the instructions provided by the grantee, which indicate installation and/or operating conditions necessary for compliance. the finished product is required to comply with all appli- cable fcc equipment auth orizations regulations, requirements and equipment functions not associated with the transmitter module portion. for example, com- pliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentio nal radiators (part 15 sub- part b unintentional radiators), such as digital devices, computer peripherals , radio receivers, etc.; and to additional authorization requirements for the non-transmitter functions on the transmitter module (i.e., verification, or declaration of conformity) (e.g., transmitter modules may also contain digital logic func- tions) as appropriate. 3.1.1 labeling and user information requirements the rn42 module has been labeled with its own fcc id number, and if the fcc id is not visible when the module is installed inside another device, then the out- side of the finished product into which the module is installed must also display a label referring to the enclosed module. this exterior label can use wording as follows: a users manual for the product should include the fol- lowing statement: additional information on labeling and user information requirements for part 15 devices can be found in kdb publication 784748 available at the fcc office of engi- neering and technology (oet) laboratory division knowledge database (kdb) http://apps.fcc.gov/oetcf/ kdb/index.cfm . contains transmitter module fcc id: t9j-rn42 or contains fcc id: t9j-rn42 this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. this equip- ment generates, uses and can radiate radio fre- quency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow- ing measures: reorient or relocate the receiving antenna. increase the separati on between the equipment and receiver. connect the equipment into an outlet on a circuit different from that to which the receiver is con- nected. consult the dealer or an experienced radio/tv technician for help. downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 13 rn42/rn42n 3.1.2 rf exposure all transmitters regulated by fcc must comply with rf exposure requirements. kdb 447498 general rf exposure guidance provides guidance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to radio frequency (rf) fields adopted by the federal communications commission (fcc). from the fcc grant: power output listed is conducted. this module must be installed by the oem or oem inte- grator. instructions on inst allation of this module may not be provided to the end user. the antenna used for this transmitter must not be co-located with any other transmitters except in accordance with fcc multi- transmitter product. procedures. installers must be pro- vided with antenna installation instructions for satisfy- ing rf exposure compliance. installers and end users must be provided with transmitter operating conditions for satisfying rf exposure compliance. 3.1.3 helpful web sites federal communications commission (fcc): http:// www.fcc.gov fcc office of engineering and technology (oet) lab- oratory division knowledge database (kdb): http:// apps.fcc.gov/oetcf/kdb/index.cfm 3.2 canada the rn42 module has been certified for use in canada under industry canada (ic) radio standards specifica- tion (rss) rss-210 and rssgen. modular approval permits the installation of a module in a host device without the need to recertify the device. 3.2.1 labeling and user information requirements labeling requirements for the host device (from sec- tion 3.2.1, rss-gen, iss ue 3, december 2010): the host device shall be properly labeled to identify the module within the host device. the industry canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the industry canada certification number of the module, preceded by the words contains transmit- ter module, or the word contains, or similar wording expressing the same meaning, as follows: user manual notice for license-exempt radio appara- tus (from section 7.1.3 rss-gen, issue 3, december 2010): user manuals for license-exempt radio appara- tus shall contain the following or equivalent notice in a conspicuous location in the user manual or alterna- tively on the device or both: transmitter antenna (from section 7.1.2 rss-gen, issue 3, december 2010): user manuals for transmit- ters shall display the following notice in a conspicuous location: the above notice may be affixed to the device instead of displayed in the user manual. 3.2.2 rf exposure all transmitters regulated by ic must comply with rf exposure requirements listed in rss-102 - radio fre- quency (rf) exposure compliance of radiocommuni- cation apparatus (all frequency bands). 3.2.3 helpful web sites industry canada: http://www.ic.gc.ca rn42: contains transmitter module ic: 6514a-rn42 this device complies with industry canada license- exempt rss standard(s). operation is subject to the following two conditions: (1 ) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'indus- trie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux con- ditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utili sateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. under industry canada regulations, this radio trans- mitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the trans- mitter by industry canada. to reduce potential radio interference to other user s, the antenna type and its gain should be so chosen that the equivalent isotrop- ically radiated power (e.i.r.p.) is not more than that necessary for successful communication. conformment la rglementation d'industrie can- ada, le prsent metteur r adio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par industrie can- ada. dans le but de rduire les risques de brouillage radiolectrique l'intentio n des autres utilisateurs, il faut choisir le type d'anten ne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. downloaded from: http:///
rn42/rn42n ds50002328a-page 14 ? 2015 microchip technology inc. 3.3 europe the rn42 module is an r&tte directive assessed radio module that is ce marked and has been manu- factured and tested with the intention of being inte- grated into a final product. the rn42 module has been tested to r&tte directive 1999/5/ec essential requir ements for health and safety (article (3.1(a)), electromagnetic compatibility (emc) (article 3.1(b)), and radio (article 3.2) and are summarized in table 3-1: european compliance test- ing. a notified body opinion has also been issued. all test reports are available on the rn42 product web page at http://www.microchip.com . the r&tte compliance association provides guid- ance on modular devices in document technical guidance note 01 available at http://www.rtteca.com/html/download_area.htm . 3.3.1 labeling and user information requirements the label on the final product which contains the rn42 module must follow ce marking requirements. the r&tte compliance association technical guidance note 01 provides guidance on final product ce mark- ing. 3.3.2 antenna requirements from r&tte compliance association document tech- nical guidance note 01 : provided the integrator installing an assessed radio module with an inte gral or specific antenna and installed in conformance with the radio mod- ule manufacturers installation instructions requires no further evaluation under article 3.2 of the r&tte directive and does not require fur- ther involvement of an r&tte directive notified body for the final product. [section 2.2.4] 3.3.3 helpful web sites a document that can be us ed as a starting point in understanding the use of short range devices (srd) in europe is the european radio communications committee (erc) recommendation 70-03 e, which can be downloaded from the european radio commu- nications office (ero) at: http://www.ero.dk . additional helpful web sites are: radio and telecommunications terminal equip- ment (r&tte): http://ec.europa.eu/enter prise/rtte/index_en.htm european conference of postal and telecommu- nications administrations (cept): http://www.cept.org european telecommunications standards insti- tute (etsi): http://www.etsi.org european radio communications office (ero): http://www.ero.dk the radio and telecommunications terminal equipment compliance association (r&tte ca): http://www.rtteca.com note: to maintain conformance to the testing listed in table 3-1 , the module shall be installed in accordance with the installa- tion instructions in this data sheet and shall not be modified. when integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essent ial requirements of the r&tte directive. downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 15 rn42/rn42n table 3-1: rn42 european compliance testing 3.4 australia the australia radio regulati ons do not provide a modu- lar approval policy similar to the united states (fcc) and canada (ic). however, rn42 module rf transmit- ter test reports can be used in part to demonstrate com- pliance in accordance with acma radio communications short range devices standard 2004 (the short range devices standard calls up the as/nzs 4268:2008 industry standard). the rn42/ rn42n module test reports can be used as part of the product certification and compliance folder. for more information on the rf transmitter test reports, contact microchip technology au stralia sales office. to meet overall australian final product compliance, the developer must construct a compliance folder contain- ing all relevant compliance test reports e.g. rf, emc, electrical safety and doc (declaration of conformity) etc. it is the responsibility of the integrator to know what is required in the compliance folder for acma compli- ance. all test reports are available on the rn42 product web page at http://www.microchip.com . for more infor- mation on australia complianc e, refer to the australian communications and media authority web site http:// www.acma.gov.au . 3.4.1 helpful web sites the australian communications and media authority: http://www.acma.gov.au . 3.5 new zealand the new zealand radio regulations do not provide a modular approval policy similar to the united states (fcc) and canada (ic). however, rn42 module rf transmitter test reports can be used in part to demon- strate compliance against the new zealand general user radio license for short range devices. new zealand radio communications (radio standards) notice 2010 calls up the as / nzs 4268:2008 industry standard. the rn42 module test reports can be used as part of the product ce rtification and compliance folder. all test reports are available on the rn42 prod- uct web page at http://www.microchip.com . for more information on the rf transmitter test reports, contact microchip technology sales office. information on the new zealand short range devices license can be found in the following web links: http://www.rsm.govt.nz/cms/licensees/types-ofli- cence/general-user-licence s/short-range-devices http://www.rsm.govt.nz/cms/policy-and-planning/ spectrum-policy-overview/legislation/gazette- notices/product-compliance/radiocommunica- tions-radiostandards-notice-2010 . to meet overall new zealand final product compliance, the developer must construct a compliance folder con- taining all relevant compliance test reports e.g. rf, emc, electrical safety and doc (declaration of confor- mity) etc. it is the resp onsibility of the developer to know what is required in the compliance folder for new zealand radio communications. for more information on new zealand compliance, refer to the web site http:/ /www.rsm.govt.nz . 3.5.1 helpful web sites radio spectrum ministry of economic development: http://www.rsm.govt.nz . certification standards article laboratory report number date safety en 60950-1:2006+a11:2009+a1:2010+a12:2011 [3.1(a)] worldwide te s t i n g services (taiwan) co., ltd. w6m21402- 13966-l 2014-03-24 health en 62479:2010 w6m21402- 13966-62479 2014-03-13 emc en 301 489-1 v1.9.2 (2011-09) [3.1(b)] w6m21402- 13966-e-16 2014-03-13 en 301 489-17 v2.2.1 (2012-09) radio en 300 328 v1.8.1 (2012-06) (3.2) w6m21402- 13966-t-45 2014-03-13 notified body opinion e u r o f i n s product service gmbh u9m-1404- 3736-c-v01 2014-04-15 downloaded from: http:///
rn42/rn42n ds50002328a-page 16 ? 2015 microchip technology inc. 3.6 japan the rn42 module has received type certification and is labeled with its own technical conformity mark and cer- tification number as required to conform to the techni- cal standards regulated by the ministry of internal affairs and communications (mic) of japan pursuant to the radio act of japan. integration of this module into a final product does not require additional radio certification provided installa- tion instructions are followed and no modifications of the module are allowed. additional testing may be required: if the host product is subject to electrical appli- ance safety (for example, powered from an ac mains), the host product may require product safety electrical appliance and material (pse) testing. the integrator s hould contact their confor- mance laboratory to determ ine if this testing is required. there is an voluntary electromagnetic compatibil- ity (emc) test for the ho st product administered by vcci: http://www.vcci.jp/vcci_e/index.html. 3.6.1 labeling and user information requirements the label on the final product which contains the rn42 module must follow japan marking requirements. the integrator of the module should refer to the labeling requirements for japan available at the ministry of internal affairs and communications (mic) website. the rn42 module is labeled with its own technical con- formity mark and certificat ion number. the final product in which this module is being used must have a label referring to the type certified module inside: 3.6.2 helpful web sites ministry of internal affairs and communications (mic): http://www.tele.soum u.go.jp/e/index.htm association of radio industries and businesses (arib): http://www.arib.or.jp/english 3.7 korea the rn42 module has received certification of confor- mity in accordance with the radio waves act. integra- tion of this module into a final product does not require additional radio certification provided installation instructions are followed and no modifications of the module are allowed. 3.7.1 labeling and user information requirements the label on the final product which contains the rn42 module must follow kc marking requirements. the integrator of the module should refer to the labeling requirements for korea available on the korea com- munications commission (kcc) website. the rn42 module is labeled with its own kc mark. the final product requires the kc mark and certificate num- ber of the module: 3.7.2 helpful web sites korea communications commission (kcc): http://www.kcc.go.kr national radio research agency (rra): http://rra.go.kr 3.8 taiwan the rn42 module has received compliance approval in accordance with the telecommunications act. cus- tomers seeking to use the compliance approval in their product should contact microchip technology sales or distribution partners to obtain a letter of authority. integration of this module into a final product does not require additional radio certification provided installa- tion instructions are followed and no modifications of the module are allowed. 3.8.1 labeling and user information requirements the rn42 module is labeled with its own ncc mark and certificate number as below: downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 17 rn42/rn42n the users manual should contain below warning (for rf device) in traditional chinese: 3.8.2 helpful web sites national communications commission (ncc): http://www.ncc.gov.tw downloaded from: http:///
rn42/rn42n ds50002328a-page 18 ? 2015 microchip technology inc. 4.0 ordering information table 4-1 provides ordering information for the rn42 module. note 1: for other configurations, contact microchip drectly. 2: it is highly recommended that customers order part numbers by specific firmware version when available to ensure consistent receipt of their designed-in firmware version. information on firmware versions can be found on the rn42/rn42n product web page and the bluetooth data module command reference and advanced information users guide . go to http://www.microchip.com for current pricing and a list of di stributors carrying microchip products. table 4-1: ordering information (1) part number (1) firmware (2) description rn42-i/rm 6.15 class 2, 2.1+edr, spp profile rn42-i/rm615 6.15 class 2, 2.1+edr, spp profile rn42-i/rm477 4.77 class 2, 2.1+edr, spp profile rn42hci-i/rm n/a class 2, 2.0+edr, hci over uart rn42hid-i/rm 6.11 class 2, 2. 1+edr, hid and spp profiles rn42u-i/rm n/a class 2, 2.0+edr, hci over usb rn42apl-i/rm 5.45 class 2, 2. 1+edr, spp and mfi profiles rn42apl-i/rm545 5.45 class 2, 2.1+edr, spp and mfi profiles rn42apl-i/rm543 5.43 class 2, 2.1+edr, spp and mfi profiles rn42n-i/rm 6.15 class 2, 2.1+edr, spp profile rn42nhci-i/rm n/a class 2, 2.0+edr, hci over uart rn42nhid-i/rm 6.11 cla ss 2, 2.1+edr, hid and spp profiles rn42nu-i/rm n/a class 2, 2.0+edr, hci over usb rn42napl-i/rm 5.45 class 2, 2. 1+edr, spp and mfi profiles downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 19 rn42/rn42n appendix a: revision history revision a (january 2015) this is the initial released version of the document in the microchip format. this replaces roving networks rn42/rn42n data sheet. downloaded from: http:///
rn42/rn42n ds50002328a-page 20 ? 2015 microchip technology inc. notes: downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 21 rn42/rn42n the microchip web site microchip provides online support via our www site at www.microchip.com . this web site is used as a means to make files and information easily available to customers. accessible by using your favorite internet browser, the web site contains the following information: product support C data sheets and errata, application notes and sample programs, design resources, users guides and hardware support documents, latest software releases and archived software general technical support C frequently asked questions (faq), technical support requests, online discussion groups, microchip consultant program member listing business of microchip C product selector and ordering guides, latest microchip press releases, listing of seminars and events, listings of microchip sales offices, distributors and factory representatives customer change notification service microchips customer notification service helps keep customers current on microchip products. subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. to register, access the microchip web site at www.microchip.com . under support, click on customer change notification and follow the registration instructions. customer support users of microchip products can receive assistance through several channels: distributor or representative local sales office field application engineer (fae) technical support customers should contact their distributor, representative or field application engineer (fae) for support. local sales offices are also available to help customers. a listing of sa les offices and locations is included in the back of this document. technical support is available through the web site at: http://microchip.com/support downloaded from: http:///
rn42/rn42n ds50002328a-page 22 ? 2015 microchip technology inc. notes: downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 23 rn42/rn42n product identification system to order or obtain information, e.g., on pricing or de livery, refer to the factory or the listed sales office . device: rn42 : uart, integral antenna rn42n : uart, external antenna rn42hci: uart, hci firmware, integral antenna rn42u : usb, integral antenna rn42apl: uart, mfi firmware temperature range: i = -40c to +85c package: * rm = radio module *all package offerings are pb (lead) free examples: a) rn42-i/rm: integral antenna, firmware version 6.15 b) rn42-i/rm615: integral antenna, firmware version 6.15 c) rn42apl-i/rm: integral antenna, firmware version 5.45, spp and mfi firmware d) rn42n-i/rm: external antenna, firmware version 6.15 part no. i rm package temperature range device xxx firmware revision number downloaded from: http:///
rn42/rn42n ds50002328a-page 24 ? 2015 microchip technology inc. notes: downloaded from: http:///
? 2015 microchip technology inc. ds50002328a-page 25 microchip received iso/ts-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the companys quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microper ipherals, nonvolatile memory and analog products. in addition, microchips quality system for the design and manufacture of development syst ems is iso 9001:2000 certified. quality management s ystem certified by dnv == iso/ts 16949 == information contained in this publication regarding device applications and the like is prov ided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application me ets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safe ty applications is entirely at the buyers risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting fr om such use. no licenses are conveyed, implicitly or ot herwise, under any microchip intellectual property rights. note the following details of the code protection feature on microchip devices: microchip products meet the specification contained in their particular microchip data sheet. microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions. there are dishonest and possibly illegal methods used to breach the code protection feature. all of these methods, to our knowledge, require using the microchip produc ts in a manner outside the operating specif ications contained in microchips data sheets. most likely, the person doing so is engaged in theft of intellectual property. microchip is willing to work with the customer who is concerned about the integrity of their code. neither microchip nor any other semiconductor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as unbreakable. code protection is constantly evolving. we at microchip are co mmitted to continuously improvi ng the code protection features of our products. attempts to break microchips code protection feature may be a violation of the digi tal millennium copyright act. if such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that act. trademarks the microchip name and logo, the microchip logo, dspic, flashflex, flexpwr, jukeblox, k ee l oq , k ee l oq logo, kleer, lancheck, medialb, most, most logo, mplab, optolyzer, pic, picstart, pic 32 logo, righttouch, spynic, sst, sst logo, superflash and uni/o are registered trademarks of microchip technology incorporated in the u.s.a. and other countries. the embedded control solutions company and mtouch are registered trademarks of microchip technology incorporated in the u.s.a. analog-for-the-digital age, bodycom, chipkit, chipkit logo, codeguard, dspicdem, dspicdem.net, ecan, in-circuit serial programming, icsp, inter-chip connectivity, kleernet, kleernet logo, miwi, mpasm, mpf, mplab certified logo, mplib, mplink, multitrak, netdetach, omniscient code generation, picdem, picdem.net, pickit, pictail, righttouch logo, real ice, sqi, serial quad i/o, total endurance, tsharc, usbcheck, varisense, viewspan, wiperlock, wireless dna, and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. silicon storage technology is a registered trademark of microchip technology inc. in other countries. gestic is a registered trademar ks of microchip technology germany ii gmbh & co. kg, a subsidiary of microchip technology inc., in other countries. all other trademarks mentioned herein are property of their respective companies. ? 2015, microchip technology incorporated, printed in the u.s.a., all rights reserved. isbn: 978-1-63276-903-9 downloaded from: http:///
ds50002328a-page 26 ? 2015 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://www.microchip.com/ support web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 austin, tx tel: 512-257-3370 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 cleveland independence, oh tel: 216-447-0464 fax: 216-447-0643 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit novi, mi tel: 248-848-4000 houston, tx tel: 281-894-5983 indianapolis noblesville, in tel: 317-773-8323 fax: 317-773-5453 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 new york, ny tel: 631-435-6000 san jose, ca tel: 408-735-9110 canada - toronto tel: 905-673-0699 fax: 905-673-6509 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2943-5100 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8569-7000 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - chongqing tel: 86-23-8980-9588 fax: 86-23-8980-9500 china - hangzhou tel: 86-571-8792-8115 fax: 86-571-8792-8116 china - hong kong sar tel: 852-2943-5100 fax: 852-2401-3431 china - nanjing tel: 86-25-8473-2460 fax: 86-25-8473-2470 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8864-2200 fax: 86-755-8203-1760 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 china - xiamen tel: 86-592-2388138 fax: 86-592-2388130 china - zhuhai tel: 86-756-3210040 fax: 86-756-3210049 asia/pacific india - bangalore tel: 91-80-3090-4444 fax: 91-80-3090-4123 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-3019-1500 japan - osaka tel: 81-6-6152-7160 fax: 81-6-6152-9310 japan - tokyo tel: 81-3-6880- 3770 fax: 81-3-6880-3771 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - kuala lumpur tel: 60-3-6201-9857 fax: 60-3-6201-9859 malaysia - penang tel: 60-4-227-8870 fax: 60-4-227-4068 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-5778-366 fax: 886-3-5770-955 taiwan - kaohsiung tel: 886-7-213-7830 taiwan - taipei tel: 886-2-2508-8600 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - dusseldorf tel: 49-2129-3766400 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 germany - pforzheim tel: 49-7231-424750 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 italy - venice tel: 39-049-7625286 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 poland - warsaw tel: 48-22-3325737 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 sweden - stockholm tel: 46-8-5090-4654 uk - wokingham tel: 44-118-921-5800 fax: 44-118-921-5820 worldwide sales and service 03/25/14 downloaded from: http:///

▲Up To Search▲

Price & Availability of RN42HID-IRM

	To Download RN42HID-IRM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .